Quick Answer:
Stripping removes the waste matrix and chads from die-cut sheets while keeping the blanks in place. Blanking then separates the blanks into individual pieces, with counting and stacking depending on machine configuration.
The typical post-press sequence is die cutting, stripping, and blanking. HUAWEI Machinery’s HWQ-920 is an automatic waste-stripping machine designed to replace manual stripping. It does not claim to perform blank separation, counting, or stacking.
Choosing the right machine depends on your production needs: whether you need waste removal, individual blank separation, or both.
What happens to a sheet after die cutting?
Die cutting cuts the outline and creases the folds. After a die-cutting pass without stripping, the sheet leaves the cutter whole: blanks, waste matrix, and chads stay connected. If that waste is still attached, stripping is your next job. If your next step needs individual blanks, blanking is the job after that. Track the handoffs: die-cut sheet, stripped sheet, separated blanks.

That separation can be manual or mechanical. Confirm where each job happens rather than assuming one machine covers the sequence.
Stripping vs blanking: what changes at the machine exit?
At the machine exit, look at what comes off. Stripping removes waste and leaves the blanks in the sheet; blanking separates them into individual blanks. QD Blanking’s guide calls the stripped output a sheet cleared of waste, with the blanks not yet separated, and describes blanking as producing a counted, stacked pile. Marbach treats precise separation and accurate stacking as conditions for downstream work. Treat counting and stacking as configuration details you must confirm.
| What to compare | Stripping | Blanking |
|---|---|---|
| Input | Die-cut sheet with waste | Die-cut or stripped sheet |
| Output | Waste removed; blanks remain in the sheet | Separated blanks; counting and stacking only if specified |
| Work left at exit | Handle stripped sheets; separate blanks if required | Move and inspect separated blanks; confirm count and stack if claimed |
| Main specification to pin down | Waste pattern, sheet format, height definitions | Separation quality, output format, count and pile height |
Use the table as a scope test. Ask what leaves the machine before relying on its label.

Why do the same words describe different jobs?
The Paperboard Packaging Council’s 2018/2019 column uses blanking for the final cutting stage that strips waste and stacks blanks, so its blanking includes waste removal. Marbach’s 2023 article places blanking after die cutting or stripping and defines it as separating individual blanks. QD’s 2026 guide keeps the stages separate and describes stripping as emptying the sheet while leaving the blanks in place. You are looking at three scopes applied to the same output.
Do not pick a definition. Ask which steps the machine performs and what leaves its exit.
Which stage is your bottleneck?
Find the work still done by hand in your plant. If your team keeps pulling waste matrix and chads from sheets, investigate a paper stripping machine. If they are separating, counting, or stacking blanks, a stripping-only machine will not remove that work. If the waste is already gone and the blanks are already apart, you do not need either machine; check whether your die cutter is now the constraint. Time each stage before you buy capacity.
Should you run the step inline, offline, or combined?
QD’s guide describes three configurations: an inline station in the die cutter, an offline machine, and a combined line. An inline setup keeps the job in one pass and one setup, but ties your post-press pace to the die cutter and its tooling. An offline machine frees the cutter but adds floor space, transport, and an operator. A combined line still needs a scope check: ask which steps it performs and what output you will get. This framework comes from one published analysis, so use it as a checklist and verify each point against your line.
Does the HWQ-920 fit your job?
If you need a stripped sheet with the blanks still in place, start with the HWQ-920 automatic waste stripping machine. The product page describes waste stripping; it makes no blanking, blank-separation, counting, or separated-blank stacking claim.
The page lists:
| Item | Specification |
|---|---|
| Maximum stripping area | 920 × 1300 mm |
| Minimum stripping area | 200 × 400 mm |
| Maximum finished-product size | 250 × 920 mm |
| Minimum finished-product size | 50 × 50 mm |
| Stripping height | 45–100 mm |
| Stripping speed | 3–5 times/min |
| Stack height | 1300 mm |
| Power supply | 380 V / 50 Hz |
| Power consumption | 10 kW |
| Machine weight | 3.5 t |
| Overall dimensions | 4200 × 3800 × 2150 mm |

Once output and size are settled, compare waste stripping machines, but check each model’s function against your job. A category listing is navigation, not proof of function.
What should your RFQ specify?
When you request a quote for a die cutting stripping machine or a blanking line, do not stop at model and speed. State the output first, then give enough detail that every quote covers the same job. This checklist adapts QD’s seven fields:
- Maximum and minimum sheet format and finished-product size.
- Board grade, gsm, flute, and thickness.
- Waste pattern and where removed waste must go.
- Required output, including whether separation, counting, and stacking are in scope.
- Quoted speed at your sheet, layout, and material, with its test basis.
- Definitions for stripping height and pile or stack height.
- Tooling, changeover, footprint, power, air, and floor loading.
- Commercial terms, exclusions, and spare-parts support.
- Acceptance trial and the method used to inspect output.
HUAWEI’s customization and installation support can cover model, layout, substrate, and electrical components; confirm the scope in your order. For acceptance, ask how trial sheets are selected and checked. HUAWEI’s quality and testing process describes company-level load testing, material trials, and remote video verification; treat those as process context, not HWQ-920 specifications.
HWQ-920 Automatic Waste Stripping Machine
HWQ-920 is designed to replace high-cost traditional manual stripping, significantly boosting post-press die-cutting efficiency.
View Product DetailsFAQ
Is stripping the same as die cutting?
No. Die cutting cuts the carton outline and creases the folds. Stripping removes the waste matrix and chads from the sheet. You get a stripped sheet with the blanks still in it.
Can one machine do both stripping and blanking?
Some configurations cover more than one post-press step, but the label does not prove scope. Ask which steps it performs and whether your output is a stripped sheet or separated blanks. For HWQ-920, the published page describes waste stripping and makes no blanking claim.
Does blanking always include counting?
Not necessarily. QD includes counting and stacking; Marbach defines blanking as separating individual blanks and treats accurate stacking as a condition for downstream work. If your line needs a count or a particular pile format, make it an explicit specification and acceptance point.
Is blanking always necessary?
Not automatically. It depends on what your next operation can accept. If you need individual blanks, blanking is in scope. If your line can handle a stripped sheet, you may not need blanking. Decide from your output.
What should you specify next?
There is no single winner in die cutting stripping vs blanking. The stages usually run in sequence, and the output your plant must handle sets the machine scope. Write down the incoming sheet, waste pattern, and output you need. Put that job in the RFQ with definitions, a speed basis, and an acceptance method. If waste removal is your job, send your sheet details and required output and check them against the HWQ-920’s published stripping scope.





