Quick Answer:
An internal hole waste removal machine clears plugs from openings already created by die cutting; it does not drill new holes. The die and its nicks define each opening, while the machine supports the sheet, registers the pile, and gives the waste a clear exit. Approve it on samples covering your smallest and largest cutouts, sheet sizes, board constructions, stack conditions, and one changeover. HUAWEI’s QF-3480 is listed for waste stripping up to a 300 × 480 mm sheet, so confirm your job fits that boundary.
This internal hole waste removal machine buyer guide begins with the cut, not the catalog label. The equipment runs after die cutting, when the outline of every handle, window, vent, or thread hole already exists. Its job is to free the waste inside those openings without damaging the sheet or disturbing the stack.
That distinction matters because “hole punch” can sound like paper drilling. In a carton plant, the holes may already exist as cut lines. The remaining problem is the plug: the piece of board inside an opening that small uncut fibers still hold. Describe it precisely and the tooling, sample trial, and quotation become easier to compare.
Why is internal hole waste harder to remove than edge waste?
Edge waste has an outside boundary, so it can be pulled away without crossing the product outline. Waste inside a closed cutout has no free edge. Removing it requires access from one side, support around the opening, and enough force to break the remaining fibers without crushing the sheet.
Small, narrow, or repeated cutouts make it harder. A long vent slot may flex before its waste releases; a small window may need finer tooling and more precise registration. The pile matters too. Misaligned sheets present each cutout at a different position, and an uneven pile meets the tooling at an angle.

How does a machine release an internal waste plug?
Die cutting cuts the opening and leaves controlled nicks. The waste stays connected until stripping so it does not fall into the stack early. The machine then registers the sheet, supports the board around the opening, and drives tooling against the plug. The plug breaks free along the nicks and follows a waste path away from the product.
This is a sequence, not a single punch. Registration positions the pattern, support prevents bending, the clearing tool applies force, and the waste path keeps removed pieces out of the pile and machine. Tooling must match the die layout, cutout geometry, sheet format, and board construction.

Why do bridges and nicks decide whether the plug comes out cleanly?
A nick is a small uncut connection between waste and the surrounding board. A bridge is similar, though the term can also mean a deliberate connection that keeps a sheet or waste section stable. In plain English, both are material that holds the pieces together until stripping.
Strong nicks can leave a plug stuck after the tooling acts, so force rises and edges may tear, crush, or delaminate. Weak nicks can release the plug during die cutting or stacking, contaminating the pile with loose waste. A clearing tool needs enough contact to move the plug without pressing on a bridge that must remain in the product.
What are the six sample checks?
Test the production combination you intend to approve, not one neat sheet with one familiar cutout. Record the result against the quotation.
1. Does the die layout match the clearing tool?
Give the machine builder the actual die, including bridges, nicks, cutout positions, and the repeat across the sheet. Confirm which openings will be cleared and which stay closed or are removed later.
A die built for manual removal may not suit machine cleaning. If tooling changes are proposed, record who supplies them, who approves the die, and the version used for acceptance.
2. Are the smallest and largest cutouts inside the tested range?
Test both extremes. A machine may clear a large window but fail on a fine vent slot, or handle a narrow cutout while marking a wide one.
The QF-3480 page does not publish a cutout-size range, so resolve this in the quotation and sample. Put your smallest and largest opening dimensions in the RFQ, and ask which test proves any range quoted.
3. Does sheet support and pile registration keep the pattern stable?
Run the sample with a real pile. Check that the sheet is held around each opening and the pattern reaches the tooling consistently. Repeat with a modest offset or cross-arranged pile if permitted.
A flexing sheet can shift the cutout relative to the tool, causing a torn edge or incomplete release. Ask how the machine references the sheet, aligns the pile, and what the operator checks between batches.
4. Does every plug have an unobstructed waste path?
Inspect the finished sheets and waste container together. Plugs should collect where the operator can handle them, not fall onto the pile, lodge under a guide, or enter a hard-to-clean area.
Broad sections, narrow strips, and small pieces move differently. Run long enough to expose a jam, then ask where each waste size goes and whether air, suction, gravity, or another method is used. The QF-3480 page does not define an automated waste-removal setup.
5. Are stack height, board construction, and pile alignment inside the tested range?
Test minimum and maximum pile heights with the board grades and thicknesses you run, including laminated or recycled stock if used. The same cutout can behave differently in softer, thicker, or more compressed board.
Measure stack height by a defined method, not by eye. The QF-3480 page does not clearly publish stack capacity or a board-thickness range; ask the machine builder to define both and identify the supporting sample.
6. Is changeover to the next job demonstrated and documented?
Include at least one changeover. Watch the tooling change, registration adjustment, and first acceptable sheets after restart. Record the time, people, tools, and setup waste.
This affects delivery and cost as much as quality. A fast cycle looks poor when changeovers consume the day. Ask for the cycle rate, then measure finished pieces per hour yourself, including loading, stoppages, rejects, and waste handling.

What should your RFQ include?
Describe the job, not just the model. Supply the die layout, sheet sizes, board grades, cutout dimensions, pile heights, and required output at the machine exit. State whether every internal opening must be cleared or only selected ones.
List tooling, changeover, waste handling, electrical and air requirements, footprint, and controls. Ask how every size or height limit is defined, especially when a catalog row is ambiguous. Separate machine, tooling, installation, training, spare parts, and delivery for a clear comparison.
HUAWEI’s customization and installation support covers model, layout, substrate, and electrical-scope adjustments; confirm what your order includes. Its quality and testing process is company-level context, not a QF-3480 guarantee. Your own sample should be the acceptance record.
Does the QF-3480 fit your job?
HUAWEI lists the QF-3480 paper hole punch machine in its waste stripping category. The published maximum sheet size is 300 × 480 mm. If your carton sheet is larger, start elsewhere, whatever the cutout pattern.
The page also lists a 120 mm maximum stroke, 800 mm worktable height, 2–3 kW motor, 220 V at 45–60 Hz, 640 × 500 × 1500 mm dimensions, and 120 kg weight. Some parameter rows appear shifted or mistranslated; confirm each value’s function in the quotation and do not treat a misplaced number as a cutout or stack limit.
The name “paper hole punch machine” can sound like hole-making equipment. Read it through the listed category and process: a candidate for clearing waste from openings already die cut, not a paper drill. The page does not publish a minimum sheet size, stack capacity, cutout range, output speed, board-thickness range, or automation level; ask before approval.
If your sheet fits but the cutouts are unusual, request a sample with your die and board. If the sheet is too large, compare the waste stripping category and screen other models by process, size, and tooling.

QF-3480 Precision Processing Equipment A compact post-processing machine designed for the efficient handling of medium and small-sized paper sheets and printed materials.
View Product DetailsIs internal hole waste removal the same as paper drilling?
No. Paper drilling makes new round holes for filing, binding, or loose-leaf products. Internal hole waste removal starts with an opening already cut in the sheet and clears the plug left inside it.
The questions differ. Drilling depends on drill diameter, stack height, spindle count, and hole spacing. Internal waste stripping depends on die layout, bridges, cutout geometry, support, registration, and waste release. If you need new holes, the MSZK-570 paper punching machine is the relevant contrast, not the QF-3480.
What should you do next?
Take one die and one production pile. Mark the smallest and largest cutouts, measure the stack, photograph the bridges, and define “clean” for each opening. Ask the machine builder to quote that scope and demonstrate it. A trial proves only the tested material and layout combination.
If the QF-3480’s 300 × 480 mm limit fits, send your die layout, board details, and sample requirements so the offer covers tooling, stack conditions, waste handling, and acceptance before price. Buy a verified process, not a label.





